THE PROP FINDER SITE
Boat Engine Brands » Evinrude Models » Evinrude 25HP E-Tec (14 Spline)

Solas then Rubex brand charts displayed.

Evinrude 25hp, E-Tec Propellers

Searched
Evinrude Solas Dealer Locator
25
E-Tec (14 Spline)
2011 - 2014
3in. Gearcase
Solas Amita 3
Aluminum - Exclusive squeeze cast process
- Stronger blades with better performance
- Outstanding acceleration and top speed
- See Amita 3 Video
Solas Amita 3 propeller for Evinrude 25 2011 - 2014
- 3 Blade Propeller
- Thru-Hub Exhaust
- Pressed Rubber Bushing
Diameter Pitch Rotation Part Number
11 9 R 2211-110-09
10.8 10 R 2211-108-10
10.5 11 R 2211-105-11
10.3 12 R 2211-103-12
10.1 13 R 2211-101-13
10 14 R 2211-100-14
10 15 R 2211-100-15
Click part numbers for dealer search.
Solas Amita 4
Aluminum - Exclusive squeeze cast process
- Stronger blades with better performance
- Great acceleration and midrange performance
- Great stern lift and handling
- See Amita 4 Video
Solas Amita 4 propeller for Evinrude 25 2011 - 2014
- 4 Blade Propeller
- Thru-Hub Exhaust
- Pressed Rubber Bushing
Diameter Pitch Rotation Part Number
10.2 11 R 2213-102-11
10.1 12 R 2213-101-12
10 13 R 2213-100-13
10 14 R 2213-100-14
10 15 R 2213-100-15
Click part numbers for dealer search.
Solas New Saturn
Stainless - All-around performance
- Good acceleration
- Large ear blade design
- See New Saturn Video
Solas New Saturn propeller for Evinrude 25 2011 - 2014
- 3 Blade Propeller
- Thru-Hub Exhaust
- Pressed Rubber Bushing
Diameter Pitch Rotation Part Number
10 3/4 10 R 2231-108-10
10 1/2 11 R 2231-105-11
10 1/4 12 R 2231-103-12
10 1/8 13 R 2231-101-13
10 14 R 2231-100-14
10 15 R 2231-100-15
Click part numbers for dealer search.
Solas HR Titan 4
Stainless - Great stern lift & acceleration
- High rake blade and cupped blade design
- Powerful thrust & very smooth performance
- Increased speed & economy in the mid-range
- See HR Titan 4 Video
Solas HR Titan 4 propeller for Evinrude 25 2011 - 2014
- 4 Blade Propeller
- Thru-Hub Exhaust
- Pressed Rubber Bushing
Diameter Pitch Rotation Part Number
10 10 R 2253-100-10
10 11 R 2253-100-11
10 12 R 2253-100-12
Click part numbers for dealer search.
Kit #17022501
Thrust Washer Spacer Nut Cotter Pin
OBTW OBSP OBNT Apin (1-1/8")
OBTW OBSP OBNT APIN
This hardware is for OEM & Solas pressed rubber hub props only (not Rubex).
Rubex 3
Aluminum - Exclusive squeeze cast process
- Stronger blades with better performance
- Outstanding acceleration and top speed
- See Rubex 3 Video
Hub Rubex 3 propeller for Evinrude 25 2011 - 2014
- 3 Blade Propeller
- Thru-Hub Exhaust
- RBX-B20 Hub Kit Required
Diameter Pitch Rotation Part Number
11 9 R 9211-110-09
10.8 10 R 9211-108-10
10.5 11 R 9211-105-11
10.3 12 R 9211-103-12
10.1 13 R 9211-101-13
10 14 R 9211-100-14
10 15 R 9211-100-15
Click part numbers for dealer search.

powered by Rubex prop finder processor v.4.2.1 © Copyright 2010-2024

Notices

• ** Disclaimer: Pitch estimates and propeller selections made by this prop finder are provided only as a general reference and may not be correct for specific boats under actual boating conditions. By using this prop finder, you agree that the Solas Science and Engineering Company, Ltd, its dealers and other host entities do not accept any liability and are not responsible for harm to persons or property, damages or costs caused by the installation, handling or use of an indicated propeller or hardware.

• It is very important to refer to your engine's Owners Manual for important safety precautions when installing a propeller.

• A new propeller's hub and blades must be checked for sufficient lower unit and trim tab clearances before use.

• Make sure all propeller hardware is installed correctly.

• Engine manufacturer recommends greasing the propeller shaft every 12 months.

• Wide open throttle RPM, with boat on the water in forward gear under normal loading conditions, should fall within the range that is recommended by the engine manufacturer and not exceed the recommended maximum. This is important in determining a suitable propeller pitch. When in doubt, dealer assistance is suggested.

• Prop installation, inspection and boat operation all need to be done in a safe and responsible manner.

* Trademarks
• Evinrude is a registered trademark of Bombardier Recreational Products, Inc
• Solas is a registered trademark of the Solas Science and Engineering Company, Ltd
• Rubex is a trademark of the Solas Science and Engineering Company, Ltd
All trademarks remain the property of their respective owners.

Note: Right (R or CW) is the standard rotation found on most single engine boats.